Product ID:CHO-SHIELD 596 PART A
MSDS Date:05/28/1986
FSC:5999
NIIN:01-192-8825
Kit Part:Y
MSDS Number: BKRDK

CHOMERICS, INC.

77 DRAGON COURT
WOBURN, MA 01888
US

Emergency Phone: 617-935-4850

Info Phone: 617-933-4318

Cage: 18565

PARKER HANNIFIN CORPORATION CHOMERICS DIVISION

WOBURN, MA 01888 US

Telephone: 617-935-4850

Cage: 18565

SILVER (SARA III)

CAS: 7440-22-4

RTECS: VW3500000

Fraction By Weight: >70%

OSHA PEL 0.01 MG/M3

ACGIH TLV: 0.1 MG/M3; 9192

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

TALC (CONTAINING NO ASBESTOS)

CAS: 14807-96-6

RTECS: VV7720000

Fraction By Weight: <5%

OSHA PEL 2 MG/M3 RDUST

ACGIH TLV: 2 MG/M3 RDUST; 9091

TOLUENE (SARA III)

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: <10%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

METHYL ISOBUTYL KETONE (SARA III)

CAS: 108-10-1

RTECS: SA9275000

Fraction By Weight: <5%

OSHA PEL 100 PPM/75 STEL

ACGIH TLV: 50 PPM/75 STEL; 9293

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

LD50 LC50 Mixture:ORAL LD50 (RAT) IS UNKNOWN.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:MAY CAUSE MODERATE EYE IRRITATION ON
DIRECT CONTACT. VAPORS FROM HEAT CURE AND DUST FROM GRINDING,
SANDING, ETC. MAY CAUSE EYE AND RESPIRATORY SYSTEM IRRITATION.
PROLONGED OR REPEATED SKIN CONTACT MAY PRODUCE SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION. INGESTION MAY CAUSE DIGESTIVE
SYSTEM IRRITATION.
Explanation of Carcinogenicity:THIS COMPOUND CONTAINS NO INGREDIENTS AT
CONCENTRATIONS OF 0.1% OR GREATER THAT ARE CARCINOGENS OR SUSPECT
CARCINOGENS.
Effects of Overexposure:MAY CAUSE EYE, SKIN & RESPIRATORY TRACT
IRRITATION. MAY CAUSE AN ALLERGIC SKIN REACTION IN CERTAIN
SUSCEPTIBLE INDIVIDUALS. INGESTION MAY CAUSE NAUSEA, VOMITING, AND
DIARRHEA.
Medical Cond Aggravated by Exposure:INDIVIDUALS WITH PRE-EXISTING SKIN,
LIVER OR KIDNEY DISORDERS ARE AT A GREATER THAN NORMAL RISK WHEN
EXPOSED TO THIS MATERIAL.

First Aid:INHALATION: REMOVE PERSON TO FRESH AIR. CALL A PHYSICIAN.
EYE: FLUSH IMMEDIATELY WITH LARGE AMOUNTS OF WATER FOR 15 MINUTES.
GET MEDICAL ATTENTION. SKIN: REMOVE CONTAMINATED CLOTHING. WASH
WITH SOAP A ND WATER PROMPTLY. INGESTION: DO NOT INDUCE VOMITING.
GET IMMEDIATE MEDICAL ATTENTION.

Flash Point:<40F (TOLUENE)
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM, OR DRY
CHEMICAL.
Fire Fighting Procedures:WEAR FIRE FIGHTING PROTECTIVE EQUIPMENT AND A
FULL FACED SELF CONTAINED BREATHING APPARATUS.
Unusual Fire/Explosion Hazard:TOXIC FUMES MAY BE EVOLVED UPON EXPOSURE
TO HEAT OR OPEN FLAMES. VAPORS ARE HEAVIER THAN AIR & MAY SETTLE IN
LOW PLACES OR TRAVEL LONG DISTANCES & IGNITE.

Spill Release Procedures:ELIMINATE IGNITION SOURCES IN AREA. WEAR
SUITABLE PROTECTIVE CLOTHING. VENTILATE SPILL AREA TO EVACUATE
VAPORS. WIPE-UP OR ABSORB WITH VERMICULITE OR OTHER ABSORBENT
MATERIAL. COLLECT WASTE IN SEALED CONTAINER. WASH AREA WITH SOAP
AND WATER.
Neutralizing Agent:MIX PART A WITH PART B.

Handling and Storage Precautions:PREVENT CONTACT WITH EYES AND SKIN.
KEEP CONTAINER CLOSED WHEN NOT IN USE. FOR INDUSTRIAL OR
PROFESSIONAL USE ONLY. FOR IMMEDIATE USE WHEN MIXED.
Other Precautions:THIS PRODUCT CONSISTS OF TWO COMPONENTS. THE
PRECAUTIONS FOR EACH COMPONENT SHOULD BE OBSERVED WHEN SEPARATE OR
MIXED. KEEP OUT OF THE REACH OF CHILDREN.

Respiratory Protection:NONE NORMALLY REQUIRED. USE NIOSH/MSHA APPROVED
DUST RESPIRATOR WHEN GRINDING OR SANDING CURED MATERIAL.
Ventilation:PROVIDE SUFFICIENT LOCAL & MECHANICAL(GENERAL) VENTILATION
IN PATTERN/VOLUME TO CONTROL INHALATION EXPOSURES.
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:CHEMICAL SAFETY GOGGLES
Other Protective Equipment:WEAR INDUSTRIAL-TYPE WORK CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER USE AND BEFORE EATING OR
SMOKING. LAUNDER CONTAMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
THIS IS A TWO PART PRODUCT. EMPTY CONTAINERS MAY RETAIN PRODUCT RESIDUE
OR VAPORS. AIRBORNE PARTICULATE MAY BE GENERATED DURING REMOVAL
OPERATIONS INCLUDING ABRASIVE BLASTING, SANDING OR GRINDING.

HCC:F2
Vapor Pres:<10
Vapor Density:>1
Solubility in Water:NEGLIGIBLE
Appearance and Odor:GRAY-COLORED PASTE, PETROLEUM SOLVENT ODOR.
Percent Volatiles by Volume:<15

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, BASES, AMINES, AMIDES, STRONG ACIDS, AND
MERCAPTANS MAY CAUSE POLYMERIZATION.
Stability Condition to Avoid:EXPOSURE TO HIGH HEAT, OPEN FLAMES AND
OTHER SOURCES OF IGNITION. AVOID STORAGE IN OPEN CONTAINERS.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE, AND
DECOMPOSITION PRODUCTS WHEN SUBJECTED TO HIGH HEAT OR FLAME.
Conditions to Avoid Polymerization:IN REACTION WITH CURING AGENTS, HEAT
MAY BE EVOLVED, POSSIBLY LEADING TO EVOLUTION OF SMOKE AND/OR
FUMES.

Waste Disposal Methods:MIX PART A WITH PART B. COMPLETELY CURE AND
DISPOSE OF FULLY CURED WASTE PRODUCT IN A SANITARY LANDFILL.
INCINERATE UNCURED BULK PRODUCT AFTER MIXING WITH FLAMMABLE
MATERIAL IN AN INDUSTRIAL FACILITY. DISPOSE OF I/A/W LOCAL, STATE
AND FEDERAL LAWS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.